Every effects pedal needs power, and the way you supply it decides how quiet the rig is. A 9 volt battery in each pedal is silent but dies mid-song. A single wall adapter with a daisy-chain cable is cheap and powers four or five pedals, but every pedal shares one ground and one supply, which is where hum and digital whine creep in. An isolated power supply gives each pedal its own output, which is the standard cure for noise and the only sensible way to run pedals that need different voltages. We ranked the pedal power supplies in our music gear catalog by number of outputs, current per output, isolation, format and what owners report.
We have not measured noise on these supplies ourselves; the verdicts rest on the spec sheets and the owner review history. Prices are not printed because they change daily; every button opens the live Amazon page. If you still run pedals on batteries, see our 9V batteries guide, and for general-purpose bricks, our 12V power adapters guide. One rule before anything else: check the voltage, the current draw and the plug polarity printed on each pedal, because the wrong voltage or polarity can destroy it. Follow the manufacturer instructions for both the pedal and the supply.
How we picked
- Pedal power only. Supplies and adapters made for effects pedals, plus one pedalboard included for its built-in supply.
- Stated outputs and current. We list the milliamps per output where the listing gives them, and say so where it does not.
- Isolation. Isolated outputs rank above shared ones for anything beyond a small, simple board.
- Voltage options. Switchable 12 and 18 volt outputs counted for players with pedals that need them.
- Owner feedback. Every pick has more than a hundred owner reviews, several of them thousands.
The picks
JOYO DC 9V Guitar Pedal Power Supply (800mA -1A) AC Wall Charger Adapter with 4 Way Daisy Chain Pedal Cables (8.8 FT), Compatible for Most Effect Pedals (Tip Negative)

For a first pedalboard this JOYO kit is the obvious buy. One wall adapter supplies 9 volts DC at 800 milliamps, 1 amp at most, with the tip-negative polarity that most guitar pedals use, and a four-way daisy-chain cable is in the box so four pedals run from a single outlet. The 100 to 240 volt input means it travels. Thousands of owners give it a very strong owner rating. Understand what a daisy chain is, though: every pedal shares the same supply and ground. Ordinary overdrives, fuzzes and tuners are usually content with that, but mixing digital delays or modellers with analog drives on one chain is the classic recipe for hum.
- Thousands of owner reviews with a very strong owner rating
- Powers four pedals from one wall plug
- Up to 1 A total is plenty for standard analog pedals
- Works worldwide on 100 to 240 volts
- Daisy chain shares ground, so noise is possible with some pedals
- 9 volts only
- High-draw digital pedals can use most of the current alone
LEKATO Guitar Pedal Power Supply, True Isolated Pedal Power Supply with 10 Ports, USB Port, Short Circuit Protection, Guitar Pedal Power DC Output 9V 12V 18V for Effect Pedal

The LEKATO is the supply most players should grow into. It has ten outputs that the maker describes as truly isolated, fed by multiple transformers, so each pedal gets its own clean feed instead of sharing one, which is the usual fix for daisy-chain hum. Seven outputs deliver 9 volts at 300 milliamps, one delivers 9 volts at 500 milliamps for a hungrier pedal, and two can be switched between 9, 12 and 18 volts for pedals that want more headroom. Every channel has its own short-circuit and over-current protection, so a fault on one output does not take down the rest, and an LED on each output shows it is live. The case is aluminum alloy and a USB port charges a phone. Hundreds of owners give it a very strong owner rating.
- Described as truly isolated, with multiple transformers
- Two outputs switch between 9, 12 and 18 volts
- 300 mA on the standard outputs covers many digital pedals
- Hundreds of owner reviews with a very strong owner rating
- Larger than a wall adapter; needs board space
- Only one 500 mA output
- Isolation is a maker claim we have not measured
WUKUR 9V Power Supply for Guitar Pedals,Compatible with Boss PSA Adapter 9V DC for Pedals Like ME-80 ME-70 ME-25 GT-100 GT-1 GT-10 BR-80 RC-1 RC-3,5.9FT/1.8M Guitar Pedal Power Cable for Effects

Sometimes all you need is one good adapter: for a multi-effects unit, a looper, or as the spare in a gig bag. The WUKUR is a regulated 9 volt DC supply built to be compatible with Boss PSA-style inputs, and the listing names units such as the ME-80, GT-1 and RC-3. The cable is 5.9 feet long. The maker makes a point many listings skip: this is a DC supply, not a 9 volt AC adapter, and a few older pedals need AC, so check the label on the pedal first. Thousands of owners give it a very strong owner rating, the largest record in this guide. The bullets we have do not state the current rating, so confirm it on the product page against the draw of a power-hungry multi-effects unit before relying on it.
- Thousands of owner reviews with a very strong owner rating
- Drop-in replacement for a Boss PSA-style adapter
- Long cable reaches the board easily
- Maker warns clearly about AC versus DC pedals
- Powers one device unless you add a daisy chain
- Current rating is not stated in the bullets
- No isolation between pedals if chained
Hiree Guitar Pedal Power Supply Adapter Station Distributor 10 Isolated DC Output for 9V/12V/18V Effect PedalBoard with 4 AC Outlet for Charging Speaker, Musical Instruments

The Hiree packs the most connections for the money: ten DC outputs plus mains outlets on the same box, so a small amp or keyboard supply can plug into the board. The DC side is seven 9 volt outputs at 100 milliamps, one 9 volt output at 500 milliamps, one 12 volt and one 18 volt output at 100 milliamps each, with separate short-circuit protection per output and a built-in noise filter. It needs no external adapter; a five-foot detachable AC cord runs straight to the unit. Read the listing with care on two points. The title promises four AC outlets while one bullet says two, with a 600 watt total, so check the photos. And 100 milliamps suits analog pedals but not most digital ones, which leaves a single 500 milliamp output for those. More than a thousand owners give it a very strong owner rating.
- More than a thousand owner reviews with a very strong owner rating
- Ten outputs at a low price
- AC outlets on the unit for an amp or keyboard supply
- No wall-wart; a detachable mains cord plugs straight in
- Listing is inconsistent on the number of AC outlets
- Seven outputs are only 100 mA each
- Fixed 12V and 18V outputs are low current

The CIOKS DC7 is the professional choice, from the Danish power supply specialist CIOKS. Its design is a two-stage switch-mode supply with multistage filtering for what the maker calls ultra-low noise, and its distinguishing feature is flexibility: each outlet offers four selectable voltages, so any outlet can serve a 9 volt overdrive or a higher-voltage pedal without a special cable. Total output is up to 48 watts, a large budget that copes with current-hungry digital reverbs and modellers. The description gives a one-inch profile and a weight of 1.1 pounds, slim enough to mount under most boards, and twelve Flex cables are included. Hundreds of owners give it an excellent owner rating. The bullets we have do not state the number of outlets, so confirm it on the product page. It costs several times the mid-range picks.
- Excellent owner rating, the highest in this guide
- Every outlet has four selectable voltages
- 48 W total handles demanding digital pedals
- One-inch profile fits under most pedalboards
- By far the most expensive pick
- Outlet count is not stated in the bullets we have
- More supply than a small board needs
Voodoo Lab Pedal Power X8 High Current Power Supply

Voodoo Lab’s Pedal Power X8 takes the opposite approach to budget bricks that mix a few strong outputs with many weak ones: all eight of its isolated outputs supply 9 volts at up to 500 milliamps, so there is no working out which pedal goes where. The maker describes a hybrid DC transformer design with zero added noise, and the unit is compact enough to mount beneath low-profile boards such as the Pedaltrain Nano and Metro, using the included 3M Dual Lock. It runs on 100 to 240 volts for touring through a supplied 12 volt adapter with a detachable line cord, and it can also be powered from the expansion port of a larger Voodoo Lab supply. More than a hundred owners give it an excellent owner rating. It offers no 12 or 18 volt outputs, so it suits boards of standard 9 volt pedals.
- All eight outputs deliver up to 500 mA
- Isolated outputs from a specialist maker
- Small enough for compact pedalboards
- Excellent owner rating from more than a hundred owners
- 9 volts only; no 12V or 18V outputs
- Premium price
- Uses an external 12V adapter
LEKATO Guitar Pedal Board, Pedal Board with Built-in Power Supply, 15.5x5.1x1.6 Inch 1.3LB, Aluminum Alloy Powered Pedal Board with Pedal Cables, Bag, Adhesive Hookside Tape

The last pick is a pedalboard, included because its power supply is built in. It is an aluminum alloy board of 15.5 by 5.1 by 1.6 inches weighing 1.3 pounds, with nine DC outputs inside the frame: five 9 volt ports at 100 milliamps, one at 300 and one at 700, plus a 12 volt port at 500 milliamps and an 18 volt port at 300, and a USB port for a phone or wireless unit. The power ports are recessed and face inward, and the main plug is right-angled, which protects the connections on stage. Rubber feet, a handle, pedal cables, a bag and adhesive hook-side tape complete the kit. Hundreds of owners give it a strong owner rating. The bullets call the ports independent but do not state that they are isolated, and the narrow deck takes one row of pedals.
- Board, power, cables and bag in one purchase
- One mains cable powers the whole board
- Recessed, inward-facing power ports are protected
- Hundreds of owner reviews with a strong owner rating
- Narrow board holds only a single row of pedals
- Isolation between outputs is not stated
- Five of the 9V outputs are only 100 mA
Compare the picks
| Product | Outputs | Current per output | Isolation | Format | Our score | Our score | |
|---|---|---|---|---|---|---|---|
JOYO 9V with daisy chainJOYO | 4-way daisy chain | 800 mA shared, 1 A max | Shared | Wall adapter | 9.2/10 | 9.2 | See price |
LEKATO 10-portLEKATO | 10 plus USB | 300 mA x7, 500 mA x1, 2 switchable | Isolated, per the maker | Aluminum brick | 9.1/10 | 9.1 | See price |
WUKUR 9V adapterWUKUR | 1 | Not stated | Single output | Wall adapter | 9.2/10 | 9.2 | See price |
Hiree 10-outputHiree | 10 DC plus AC outlets | 100 mA x7, 500 mA x1 | Isolated per title | Brick with mains cord | 9/10 | 9.0 | See price |
CIOKS DC7Cioks | Not stated in bullets | 48 W total | Low-noise switch-mode | Slim under-board unit | 9.5/10 | 9.5 | See price |
Voodoo Lab Pedal Power X8Voodoo Lab | 8 | 500 mA each | Isolated | Compact under-board unit | 9.2/10 | 9.2 | See price |
LEKATO powered pedal boardLEKATO | 9 plus USB | 100 to 700 mA | Not stated | Pedalboard with supply | 8.8/10 | 8.8 | See price |
Isolated supply or daisy chain?
A daisy chain is fine for a handful of low-draw analog pedals and costs almost nothing. Its weakness is that all pedals share one supply and one ground path, so noise from one, typically a digital pedal, can reach the others. An isolated supply gives each output its own electrically separate feed, which removes that route. If your board is three or four drives and a tuner, start with the JOYO. If it has digital pedals, more than five pedals, or you can already hear hum that disappears on batteries, an isolated supply such as the LEKATO, the Voodoo Lab or the CIOKS is the fix.
Working out how much current you need
Every pedal states its current draw in milliamps, on the case or in the manual. Analog overdrives, fuzzes and compressors usually draw under 50 milliamps; digital delays, reverbs, loopers and modellers commonly draw from 100 to 500. An output must be rated at or above what its pedal draws, and extra capacity is harmless, since a pedal takes only what it needs. So list your pedals, mark the hungry ones, and make sure the supply has enough high-current outputs for them. This is where the Hiree, with seven 100 milliamp outputs, differs from the Voodoo Lab at 500 across the board.
Voltage and polarity: the two ways to kill a pedal
Most guitar pedals use 9 volts DC with a center-negative barrel plug, but not all. Some run on 12 or 18 volts, a few older designs need AC, and some non-guitar gear is center-positive. Feeding 18 volts to a pedal built for 9, or reversing the polarity, can destroy it instantly, and so can an AC adapter on a DC pedal, which is the warning WUKUR prints in its listing. Before connecting anything, read the label beside the power jack of the pedal. On supplies with switchable outputs, set the voltage first and connect the pedal second.
What is an isolated pedal power supply?
It is a supply where each output is electrically separate from the others, so pedals do not share a ground or power rail. That stops noise from one pedal reaching another and avoids ground-loop hum. The LEKATO 10-port, Voodoo Lab X8 and CIOKS DC7 are the isolated or low-noise picks here.
Can I power all my pedals with one adapter and a daisy chain?
Yes, if they all use the same voltage and polarity and their total draw is under the adapter rating. The JOYO supplies 800 milliamps with a four-way chain. Mixing digital and analog pedals on one chain often causes noise, in which case use an isolated supply.
How many milliamps does a guitar pedal need?
It varies. Many analog pedals draw under 50 milliamps, while digital delays, reverbs and modellers often draw 100 to 500. Check the figure on the pedal or in its manual and use an output rated at least that high. Higher-rated outputs do no harm.
Can I use an 18V output on a 9V pedal?
Only if the pedal maker says it accepts 18 volts. Some overdrives are designed for it and gain headroom; most pedals are not and can be damaged. When in doubt use 9 volts, and set any switchable output before plugging the pedal in.
Why does my pedalboard hum?
Common causes are a shared daisy chain carrying noise between pedals, a ground loop, a supply with too little current, or a noisy adapter. Try each pedal alone, then on a battery. If the hum disappears on batteries, an isolated power supply usually solves it.
Prices and stock change daily. The buttons above open Amazon so you always see the current price. Do Best Deal may earn a commission if you buy through them, at no extra cost to you.
Do Best Deal is a participant in the Amazon Services LLC Associates Program. As an Amazon Associate we earn from qualifying purchases. If you buy through links on this site we may earn a commission, at no extra cost to you. Learn more.




