An LED strip is only as good as the supply feeding it. Too little current and the far end of the run dims or flickers; the wrong voltage and a 12 volt strip dies in seconds on a 24 volt supply; an indoor brick in a damp soffit fails by the first winter. The products sold as LED drivers and low-voltage power supplies fall into three shapes: sealed waterproof drivers for outdoor and damp locations, plug-in desktop bricks with a barrel jack, and open-frame enclosed supplies with screw terminals that feed long runs, 3D printers and camera systems. We ranked the ones in our tools catalog by output, enclosure, stated protections, certification and what hundreds or thousands of owners report.
We have not bench-tested these supplies ourselves; the verdicts rest on the spec sheets and the owner review history. Prices are not printed because they change daily; every button opens the live Amazon page. Small wall adapters for routers and single gadgets are covered in our 12V power adapters guide, and adjustable supplies for electronics work in our bench power supplies guide. These are mains-voltage products: match the voltage and current ratings to your load, follow the manufacturer instructions, and use a qualified electrician for any hard-wired installation.
How we picked
- On-topic supplies only. Dedicated LED drivers and 12V or 24V DC supplies of 60 watts and up; small single-gadget wall adapters were left to their own guide.
- Clear output figures. Voltage, current and wattage had to be stated plainly in the listing.
- Enclosure matched to the job. Sealed IP67 for outdoors, plug-in bricks for simple indoor runs, enclosed terminal supplies for high current.
- Stated protections and certification. Short-circuit, overload and over-temperature protection counted, and a named safety listing counted more.
- Owner feedback. Every pick has hundreds or thousands of owner reviews and a solid rating or better.
The picks
LED Driver 60 Watts Waterproof IP67 Power Supply Transformer Adapter 100V-260V AC to 12V DC Low Voltage Output for LED Light, Computer Project, Outdoor Light and Any 12V DC led Lights

This is the driver to buy when the supply has to live outdoors or in a damp spot. It converts 100 to 260 volts AC to 12 volts DC at up to 5 amps, 60 watts, inside a sealed aluminum housing that the maker rates IP67 for outdoor use and that also acts as a heat sink. Protection covers short circuit, overload, over-voltage, over-current and over-temperature, in a hiccup mode that recovers automatically once the fault is removed. The listing is upfront that the driver is not dimmable from the AC side; it works with low-voltage RGB dimmers and controllers placed after it. Certifications named are IP67, CE, RoHS and SELV; a UL or ETL listing is not mentioned, which matters if your inspector asks. More than a thousand owners give it a very strong owner rating, the deepest record of any sealed driver here. For deck, soffit, sign and landscape strip lighting on 12 volts, it leads.
- More than a thousand owner reviews with a very strong owner rating
- IP67 sealed aluminum housing for outdoor use
- Hiccup-mode protection that recovers once the fault is removed
- Wide 100 to 260 volt AC input
- Not dimmable from a wall dimmer
- 60 W ceiling limits long strip runs
- No UL or ETL listing named in the bullets
MEAN WELL LRS-350-12 Switching Power Supply 348W 12V 29Amp Single Output (LRS Series 350W 12V) for LED Project

The LRS-350-12 is the supply behind a great many serious LED and 3D printer builds, and the listing explains why in five short lines: 12 volts at a rated 29 amps and 348 watts, UL and CE certification, and full protection against short circuit, overload, over-voltage and over-temperature. The input range is chosen with a switch, 90 to 132 volts or 180 to 264 volts, and it ships set to 115 volts for the US and Canada; check that switch before you power it. A built-in fan is thermostatically controlled, starting when the internal sensor reaches 50 C and stopping below 40 C, so it is silent at light loads. Hundreds of owners give it an excellent owner rating, the highest in this guide. This is an enclosed terminal-block supply, not a plug-in brick: the mains connection needs proper wiring, a cover and, for a permanent install, an electrician.
- Excellent owner rating from hundreds of owners
- UL and CE certification named in the listing
- Fan only runs when the unit is warm
- Nearly 350 W from a single 12V output
- Open terminals must be enclosed and wired with care
- Input range is set by a manual switch
- Indoor use only; no moisture protection
ALITOVE 24V 5A Power Supply 120W DC 24V Transformer 5Amp 4A 3A, 2-Pack

For 24 volt strips, pumps and monitors that take a barrel plug, this ALITOVE two-pack is the easy answer, and it has the largest review count in the guide: thousands of owners and a strong owner rating. Each brick takes 100 to 240 volts AC and delivers 24 volts DC at up to 5 amps, 120 watts, through a 5.5 by 2.5 mm center-positive plug that the maker says also fits 5.5 by 2.1 mm jacks. Stated protections cover overload, over-voltage, over-current, over-temperature and short circuit, and the listing names FCC, CE, 3C and RoHS compliance. The maker recommends running at less than 80 percent of full load, which is good practice for any supply and means planning on roughly 96 watts per brick. It is an indoor desktop supply with no moisture protection. Buy it when you have two 24 volt runs to feed.
- Thousands of owner reviews with a strong owner rating
- Two 120 W bricks in one pack
- No wiring: barrel plug on the output
- Maker advises staying under 80 percent load, a sensible guide
- Desktop brick, not weatherproof
- Barrel plug needs an adapter for bare-wire strips
- More supply than a short strip needs
EMITEVER 24V 60W Power Supply,2.5A UL-Listed LED Adapter,Class 2

The EMITEVER is the pick for under-cabinet and shelf lighting where you want a listed, low-risk supply. It is a plug-in adapter that turns 100 to 240 volts AC into a constant 24 volts DC at up to 2.5 amps, 60 watts, and the listing describes it as cUL Listed and Class 2, the power-limited category that many low-voltage lighting installs call for. The output cable ends in a standard 5.5 by 2.1 mm jack with a positive tip. The maker is candid about limits: the supply is IP30, so dry indoor locations only; it takes one to three seconds to start, by design; and it has no dimming function, so dimming must be done with a PWM controller on the DC side. Protections include overcurrent, short circuit, overvoltage and overheat. Hundreds of owners give it a very strong owner rating. Confirm your strip is 24 volts and under 60 watts.
- Safety listing and Class 2 rating named in the listing
- Plugs straight into a wall outlet, no hard wiring
- Hundreds of owner reviews with a very strong owner rating
- Honest notes about start-up delay and dimming
- 60 W limit
- Dry indoor use only
- No dimming; needs a PWM controller on the DC side
SUPERNIGHT 12V 30A Switching Power Supply, 110-240 Volt AC to DC 360W

SUPERNIGHT’s 12 volt, 30 amp supply is the value route to 360 watts. The listing gives a 100 to 240 volt input, a 12 volt DC output at up to 30 amps, and an output voltage that can be adjusted by plus or minus 10 percent, which is useful for trimming the voltage up slightly to offset drop on a long run. A protection chip covers overload, short circuit and over-heating with automatic recovery, and the maker promises one year of replacement cover. It is sold for 3D printers, ham radio, RC chargers and LED strips, and hundreds of owners give it a strong owner rating. What the bullets we have do not state is a UL or similar listing, or any detail of the case and cooling, which is why the documented MEAN WELL ranks higher. Treat it as a project supply that needs careful wiring.
- Hundreds of owner reviews with a strong owner rating
- 360 W for long 12V strip runs and printers
- Output can be trimmed up or down by 10 percent
- One-year replacement promise
- No safety listing named in the bullets
- Case and cooling are not described in the listing
- Needs wiring and an enclosure, like any terminal supply
LED Driver 60 Watts 24V DC Low Voltage Transformer, Waterproof IP67 LED Power Supply, Adapter with 3-Prong Plug 3.3 Feet Cable for Any 24V DC led Lights, Computer Project, Outdoor Light

This is the 24 volt sibling of our top pick, and the one to choose when the strip or fixture is a 24 volt type, which is common on longer runs because higher voltage loses less along the tape. It accepts 90 to 265 volts AC and delivers 24 volts DC at 2.5 amps, 60 watts, from the same sealed IP67 aluminum housing, with the same hiccup-mode protection against short circuit, overload, over-voltage, over-current and over-temperature. This version is listed with a three-prong plug on a 3.3 foot cable, so it can go straight into an outdoor-rated receptacle without splicing the input. Like the 12 volt model it is not dimmable from the AC side and works only with low-voltage RGB dimmers after it. Hundreds of owners give it a very strong owner rating. It ranks sixth only because its review history is a fraction of the 12 volt model’s.
- Very strong owner rating from hundreds of owners
- IP67 housing for outdoor 24V lighting
- Comes with a 3-prong plug and cord attached
- Hiccup-mode protection with auto-recovery
- Not dimmable from a wall dimmer
- 60 W ceiling
- Fewer reviews than the 12V version
ALITOVE DC 24V 15A 360W Power Supply Universal Regulated Switching Transformer Adapter LED Driver 110V/220V AC Input for LED Strip CCTV Radio

When a 24 volt installation outgrows a desktop brick, this ALITOVE enclosed supply provides 15 amps and 360 watts from one box. The input is 110 or 220 volts AC, the output voltage can be trimmed by 5 percent, and there are three sets of output terminals, so separate strip runs or camera feeds can each have their own pair. A built-in fan and temperature detector keep the fan off until the inside reaches 113 F (45 C). Stated safety features are automatic overload cut-off, over-voltage cut-off, thermal cut-off and short-circuit protection, and the maker says plainly that it is for indoor use only. Hundreds of owners give it a solid owner rating, the lowest of the seven, and the bullets name no safety listing, so it ranks last. For a workshop, signage project or CCTV cabinet on 24 volts, it supplies the current the smaller picks cannot.
- 360 W at 24V for large strip installs
- Three output channels to split runs
- Temperature-controlled fan stays off when cool
- Hundreds of owner reviews with a solid owner rating
- Lowest owner rating in this guide
- Indoor use only, per the maker
- No safety listing named in the bullets
Compare the picks
| Product | Output | Power | Type | Enclosure | Our score | Our score | |
|---|---|---|---|---|---|---|---|
IP67 LED driver 12VNIYIPXL | 12V, 5A | 60 W | Sealed driver | IP67 aluminum | 9/10 | 9.0 | See price |
MEAN WELL LRS-350-12MEAN WELL | 12V, 29A | 348 W | Enclosed terminal supply | Indoor, fan cooled | 9.3/10 | 9.3 | See price |
ALITOVE 24V 5A 2-packALITOVE | 24V, 5A each | 120 W each | Plug-in brick | Indoor | 8.8/10 | 8.8 | See price |
EMITEVER 24V 60WEMITEVER | 24V, 2.5A | 60 W | Wall plug-in adapter | IP30, dry indoor | 9/10 | 9.0 | See price |
SUPERNIGHT 12V 30ASUPERNIGHT | 12V, 30A | 360 W | Terminal supply | Not stated | 8.8/10 | 8.8 | See price |
IP67 LED driver 24VNIYIPXL | 24V, 2.5A | 60 W | Sealed driver with plug | IP67 aluminum | 9.1/10 | 9.1 | See price |
ALITOVE 24V 15AALITOVE | 24V, 15A | 360 W | Enclosed terminal supply | Indoor, fan cooled | 8.4/10 | 8.4 | See price |
How to size a supply for LED strips
Start with the strip, not the supply. Find its voltage, 12 or 24, and its watts per foot or per meter, then multiply by the length you will run. A strip that draws 4 watts per foot over 20 feet needs 80 watts. Add headroom: ALITOVE itself advises staying under 80 percent of the rated load, so that 80 watt run wants a supply of at least 100 watts. More capacity does no harm, because a strip only draws what it needs; a higher voltage does, and will destroy a strip at once. If a long run looks dim at the far end, feed power at both ends or split the run.
Sealed, plug-in or terminal block?
Choose the enclosure by the location. Outdoors, in soffits, or anywhere damp, use a sealed driver such as the two IP67 picks, and keep the connections themselves inside a weatherproof box. For dry indoor shelves and cabinets, a plug-in adapter like the EMITEVER or a desktop brick is simplest, because nothing on the mains side is exposed. Enclosed terminal supplies such as the MEAN WELL, SUPERNIGHT and the 15 amp ALITOVE deliver far more current, but their mains terminals are bare: they belong inside an enclosure, with correctly rated wire, a fuse and a ground connection. If the work involves connecting to house wiring, it is a job for a qualified electrician.
Dimming, flicker and start-up delay
None of these supplies is a dimmable driver in the wall-dimmer sense. Both IP67 drivers state that they are not dimmable and work only with low-voltage dimmers, and EMITEVER says the same and points to a PWM controller on the DC side. That is the normal arrangement for strip lighting: the supply provides a steady voltage and a controller between it and the strip handles brightness and color. A short pause at switch-on is also normal; EMITEVER quotes one to three seconds. Flicker, on the other hand, usually means an overloaded supply or a wall dimmer wired ahead of a non-dimmable driver.
What is the difference between an LED driver and a power supply?
In strip lighting the terms are used for the same thing: a constant-voltage supply that turns mains AC into 12 or 24 volts DC. Every pick here is constant voltage. Constant-current drivers, used inside some fixtures, are a different product.
Can I use a 24V supply on a 12V LED strip?
No. Too much voltage destroys the strip almost at once. Match the supply voltage to the strip exactly. Extra current capacity is fine, because the strip only draws what it needs, but the voltage must be the same.
How many watts do I need for my LED strip?
Multiply the watts per foot of the strip by the length of the run, then add about 20 percent headroom. An 80 watt run is comfortable on a 100 or 120 watt supply. The 60 watt picks suit short runs and the 348 and 360 watt picks suit large projects.
Can these LED drivers be used outdoors?
Only the two IP67 drivers are described as waterproof for outdoor use. The EMITEVER is rated IP30 for dry indoor locations, and ALITOVE states its enclosed supplies are for indoor use only. Even with a sealed driver, keep the wire connections in a weatherproof box.
Do I need an electrician to install an LED power supply?
Plug-in adapters and bricks need no wiring on the mains side. Enclosed terminal supplies and any hard-wired driver connect directly to mains voltage, so follow the manufacturer instructions and use a qualified electrician for permanent or hard-wired work.
Prices and stock change daily. The buttons above open Amazon so you always see the current price. Do Best Deal may earn a commission if you buy through them, at no extra cost to you.
Do Best Deal is a participant in the Amazon Services LLC Associates Program. As an Amazon Associate we earn from qualifying purchases. If you buy through links on this site we may earn a commission, at no extra cost to you. Learn more.
